Welcome to Vbond

You stand back and admire the finished facade—the panels gleam. The lines are crisp.
Then the sun hits the building at a certain angle. You see them. Waves. Ripples. Distortion across the once-flawless surface.
The panels are flat. The material is premium. The installation looks perfect. But the oil canning is unmistakable.
The problem is not the Alucobond sheet. The problem is how you fixed it.
This guide explains why screw-fixed Alucobond panels are more prone to oil canning than floating systems. You will learn the physics behind the failure. You will understand how fixing methods affect panel flatness. And you will know exactly which fixing system to specify for a distortion-free facade.
Part 1: What Is Oil Canning?
Oil canning, also known as elastic buckling or stress wrinkling, refers to the visible waviness or rippling that can occur on the surface of flat metal panels. The term comes from the visual similarity to the bottom of an old-fashioned oil can, which pops in and out.
Key characteristics:
- Subtle waves, shadows, or ripples across flat panel surfaces
- More noticeable at certain viewing angles and under specific lighting conditions
- Cosmetic only—does not compromise panel strength or weather resistance
- Generally not reversible after installation
What oil canning is NOT:
- It is not a material defect
- It is not delamination or blistering
- It is not a structural failure
Oil canning is a cosmetic issue. But on a premium facade, cosmetics are everything.
Part 2: The Physics of Thermal Expansion
Alucobond expands and contracts with temperature changes. The linear thermal expansion coefficient is 2.4 mm per meter for every 100°C temperature difference.
In plain English:
A 1-meter-long Alucobond sheet expands by 2.4 mm when its temperature rises by 100°C. A 3-meter sheet expands by 3.6 mm. A 4-meter sheet expands by 4.8 mm.
For a real-world example:
Take a 3-meter panel. Expected heating of the panel is approximately 70°C (measured on a black panel at an air temperature of 40°C). With an assembly temperature of 20°C, the temperature difference is 50°C. Total expansion: 3.6 mm.
A 4-meter panel in a 60°C temperature swing expands by nearly 6 mm.
The core makes it worse.
The aluminum skins expand at the standard rate. But the polyethylene core expands at approximately 1.5×10⁻⁴/°C—nearly six times more than the aluminum. This mismatch creates internal stress. The core wants to expand more than the skins allow. That stress concentrates at the bond line.
Part 3: The Problem with Screw-Fixed Systems
When you screw-fix a panel rigidly at every attachment point, you create a problem. The panel wants to expand. The screws say no. The stress has nowhere to go.
The mechanism:
1. The sun heats the panel. The aluminum expands. The PE core expands even faster.
2. Screw-fixed fasteners lock the panel in place. The panel cannot move outward.
3. Stress builds inside the panel. The panel has two choices: stretch the aluminum beyond its limit, or buckle.
4. The panel buckles between the screw points.
5. Waves and ripples appear across the surface.
The evidence:
The ALUCOBOND specification explicitly requires that "the cladding be fabricated and installed to allow for all expansion and contraction of the components". When panels are fixed too rigidly, the metal will warp—pillow or oil-can—as it heats up and expands.
The screw-fixed problem:
- Multiple screws create multiple fixed points
- The panel is locked in place at every attachment
- Thermal stress cannot dissipate
- The stress accumulates between the fixed points
- The panel buckles into visible waves
Part 4: The Solution — Floating Systems
Floating systems solve the problem by allowing the panel to move. One fixed point anchors the panel. All other attachments slide.
How floating systems work:
- Each panel has one "dead fix" (fixed point), usually positioned centrally
- All other fixings feature oversized or slotted holes
- The panel can expand and contract freely in every direction from the fixed point
- Stress does not build up. The panel stays flat.
The key principle from ALUCOBOND guidelines:
"To avoid any tension occurring in the rivet and screw connections, the rivets and screws must be set tension-free. The bore holes in the panels must be large enough to allow for the expected thermal expansion".
The evidence:
Floating systems have been proven to prevent oil canning. They accommodate thermal expansion without causing distortion or buckling.
Part 5: The Numbers — 3mm vs 4mm Vulnerability
A 3mm Alucobond sheet has less thickness than a 4mm Alucobond sheet. Less thickness means less rigidity. Less rigidity means more susceptibility to oil canning.
Factor | 3mm Sheet | 4mm Sheet |
Flexural rigidity | Lower (1,250 kNcm²/m) | Higher (2,400 kNcm²/m) |
Rigidity relative to 4mm | 48% less stiff | Baseline |
Vulnerability to oil canning | Higher | Lower |
Recommended fixing | Floating only | Floating preferred |
What this means for your project:
A 3mm panel is more vulnerable to oil canning than a 4mm panel. Screw-fixing a 3mm Alucobond sheet is a recipe for visible distortion. The panel has less inherent stiffness to resist the stress created by rigid fixings.
Both 3mm and 4mm sheets require floating systems for oil canning prevention. The thinner the panel, the more critical the fixing system.
Part 6: Direct Comparison — Screw-Fixed vs. Floating Systems
Factor | Screw-Fixed (Rigid) | Floating System | Winner |
Thermal movement | Restricted completely | Allowed freely | Floating |
Oil canning risk | High | Low | Floating |
Stress on adhesive bond | High—stress concentrates | Low—stress dissipates | Floating |
Blister risk | Higher | Lower | Floating |
Fastener failure | Common—screws back out | Rare—fasteners slide | Floating |
Installation time | Faster | Slower | Screw-fixed |
Long-term performance | Poor | Excellent | Floating |
Screw-fixed panels are cheaper and faster to install. But the cost of oil canning—in client complaints, rework, and reputation damage—far exceeds the initial savings.
Part 7: The Hole Size Rule — Critical for Floating Systems
The hole in the panel must be large enough to allow for expansion. If the hole is too small, the panel cannot move. The stress transfers to the fasteners. The panel buckles.
The rule from ALUCOBOND technical guidelines:
"With the shaft of the rivet fitting closely to the edge of the hole, the attachment head must cover over 1 mm of the area surrounding the hole".
Component | Requirement |
Hole in the panel | Larger than the fastener shaft |
Attachment head | Covers at least 1 mm beyond the hole edge |
Rivet shaft | Fits closely to the hole edge |
Drilling method | Centrally drilled using multi-step drills or sleeves |
Rivet attachment jigs are used for fitting blind rivets without jamming, allowing for a tolerance of 0.3 mm.
Part 8: How to Prevent Oil Canning
1. Specify floating fixing systems
Never screw-fix Alucobond panels rigidly at multiple points. Use floating systems with oversized holes and sliding connections.
2. Use one fixed point per panel
Design one "dead fix" (fixed point), usually positioned centrally. All other fixings should be sliding.
3. Size holes correctly
The hole must be larger than the fastener shaft. The attachment head must cover at least 1 mm beyond the hole edge.
4. Leave expansion gaps
Allow 8-12 mm gaps between panels. For runs exceeding 6 meters, physical expansion joints are required.
5. Choose the right panel thickness
For large-format facades, specify 4mm panels over 3mm. The extra stiffness reduces oil canning risk.
6. Install at the right temperature
Installation temperature affects how much the panel will expand and contract. Avoid installing in extreme heat or cold.
The Prevention Flowchart
Start
│
▼
Select panel thickness
├─── 3mm panel ───► Extra vulnerable to oil canning
└─── 4mm panel ───► More rigid, lower risk
│
▼
Specify floating fixing system
├─── One fixed point per panel
└─── All other fixings sliding
│
▼
Size holes correctly
├─── Larger than fastener shaft
└─── Attachment head covers ≥1mm beyond hole
│
▼
Design expansion gaps (8- 12 mm minimum)
│
▼
For runs exceeding 6m: add expansion joints
│
▼
Install at moderate temperatures
│
▼
Inspect for early signs of oil canning
│
▼
DONE ───► Flat Alucobond facade with no oil canning
What to Ask Your Supplier
When you purchase a 3mm or 4mm Alucobond sheet for your project, ask these questions:
1. What fixing system do you recommend? The answer should be a floating system, not screw-fixed.
2. What hole size do you recommend for thermal expansion? The hole must allow for expansion—the attachment head must cover at least 1mm beyond the hole.
3. What expansion gap do you recommend? The answer should be 8- 12 mm minimum.
4. What is your panel's oil canning resistance? Premium panels from a reputable manufacturer resist oil canning better than low-quality alternatives.
5. Do you provide installation guidelines for floating systems? A reliable supplier will have documented procedures.
The Bottom Line
Screw-fixed Alucobond panels are more prone to oil canning because they restrict thermal movement. The panel wants to expand. The screws say no. Stress builds. The panel buckles. Waves appear.
Floating systems prevent oil canning because they allow the panel to move. One fixed point anchors the panel. All other attachments slide. The panel expands and contracts freely. Stress does not build. The panel stays flat.
The physics is clear: Alucobond expands at 2.4 mm per meter for every 100°C temperature change. A 4-meter panel in a 50°C swing moves nearly 5 mm. A 3-meter panel in the same swing moves 3.6 mm. Without room to move, that force causes oil canning.
A 3mm Alucobond sheet is even more vulnerable. It has less stiffness than a 4mm Alucobond sheet. Less stiffness means more susceptibility to distortion. Screw-fixing a 3mm panel is a recipe for visible waves.
The solution is straightforward:
- Specify floating fixing systems
- Use one fixed point per panel
- Size holes correctly (1mm head coverage minimum)
- Leave 8- 12 mm expansion gaps
- Add expansion joints for runs exceeding 6 meters
When you walk that site twelve months from now, standing in front of a flat, flawless Alucobond facade with no oil canning in sight, you will know—not hope, not guess, but know—that the fixing system was right. Because you specified floating. Because you sized the holes correctly. Because you refused to let rigid screws destroy a premium facade.
The panel is only as flat as the fixing system behind it. Choose floating. Choose flatness. Your facade depends on it.